¿COMO SE MIDE LA CORRIENTE DIRECTA?
Para medir corriente
directa se utiliza el multímetro como amperímetro y se selecciona, en el
multímetro que estemos utilizando, la unidad (amperios) en DC (c.d.). Se revisa
que los cables rojo y negro estén conectados correctamente.
Se selecciona la
escala adecuada, si tiene selector de escala (si no tenemos idea de que
magnitud de la corriente directa que vamos a medir, escoger laescala mas
grande). Si no tiene selector de escalaseguramente el multímetro escoge la
escalaautomáticamente.
Para medir una
corriente con el multímetro, éste tiene que ubicarse en el paso de la corriente
que se desea medir. Para esto se abre el circuito en el lugar donde la
corriente a medir y conectamos el multímetro (lo ponemos en “serie”).
Si la lectura es negativa significa que la corriente en el componente, circula en sentido opuesto al que se había supuesto, (normalmente se supone que por el cable rojo entra la corriente al multímetro y por el cable negro sale). En algunas ocasiones no es posible abrir el circuito para colocar el amperímetro. En estos casos, si se desea averiguar la corriente que pasa por unelemento, se utiliza la Ley de Ohm.
Se mide la tensión
que hay entre los terminales del elemento por el cual pasa la corriente que se
desea averiguar y después, con la ayuda de la Ley de Ohm (V = I x R), se
obtiene la corriente (I = V/R). Para obtener una buena medición, se debe tener
los valores exactos tanto del voltaje como de la resistencia.
Otra opción es
utilizar un amperímetro de gancho (que puede ser un amperímetro analógico o un
amperímetro digital) que permite obtener la corriente que pasa por un circuito
sin abrirlo. Este dispositivo, como su nombre lo indica, tiene un gancho que se
coloca alrededor del conductor por donde pasa la corriente y mide el campo
magnético alrededor de él. Esta medición es directamente proporcional a la
corriente que circula por el conductor y que se muestra con una aguja o
pantalla.
Notas:
- Multímetro = VOM = Tester = Polímetro
- Amperímetro se llama, en este caso, al multímetro preparado para medir corriente.
How to measure direct current?
To measure DC multimeter as an ammeter is used and in the meter we are
using, select the drive (amps) in DC (D.C.). We review the red and black
cables are properly connected.
the appropriate scale is selected, if you have scale selector (if we
have no idea that magnitude of the direct current that we measure,
choose larger scale will test). If no selector escalaseguramente the
multimeter chooses escalaautomáticamente.
To measure a current with the meter, it must be located in the passage
of the current to be measured. For this, the circuit is opened at the
place where the current to be measured and connect the multimeter (put
it in "series").
If the reading is negative means that the current component, flowing in
the opposite direction than had been assumed, (usually it is assumed
that the red current cable enters the multimeter and the black wire
out). Sometimes it is not possible to open the circuit to place the
ammeter. In these cases, if you want to find out the current through
unelemento, Ohm's Law is used.
Measure direct current (DC) - Electronics Area
the tension between the terminals of the element through which passes
the current sedesea find and then, with the help of Ohm's Law (V = I x
R) is measured, the current (I = V / R) is obtained . For a good
measurement, it must be the exact values of the voltage as much
resistance.
Another option is to use an ammeter hook (which may be an analog or
digital ammeter ammeter) for obtaining the current through a circuit
without opening it. This device, as its name implies, has a hook that is
placed around the conductor through which the current and measures the
magnetic field around it. This measurement is directamenteproporcional
the current flowing through the conductor and shown with a needle or
screen.
Notes:
Multimeter VOM = = = Multimeter Tester
Ammeter is called, in this case, the multimeter prepared to measure current.

No hay comentarios.:
Publicar un comentario